![]() I did notice that I still had another splitter mounted next to the directv splitter. I am thinking it comes from the AT&T box on the outside of my house. I guess I need to take a look and see where that main coax cable that is connected to the IN port actually comes from. Under my house I have one coax cable that is connected to the IN port of the directv splitter and I have three other coax cables connected to the splitter. prior to connecting the MoCA adapters all of my Uverse receivers were using the coaxial cables for a wired connection. All of my services are Uverse ( phone, TV, and Internet). No I don't have cable TV or cable internet. So do you recommend that I install a MoCA certified three way splitter of my own? I have some good high quality ones that I bought whenever I had cable tv and used a Tivo system? I'm thinking I need to do that and attach the POE filter.any help appreciated.īut will say so far I am blown away at the speed I now get throughout my whole house and also those Netgear switches are working great too. So whenever I put the MoCA adpater on that directv splitter it killed my speeds. I went under the house to install a MoCA POE filter and I remember that whenever the AT&T technician was here to hook up my IPTV I had once had Directv and he didn't have a three way splitter on him but he said since we own Directv I can just use the directv splitter. The Motorola MoCA adapters are working great so far! I can pull in the mid 800's at any of the three locations where I have the MoCA adpaters (hardwired of course) I am pulling in the mid 700's from my main access point and the downstairs access point via wifi which is impressive. Ok got everything connected up yesterday and wanted to share the results. | -> ethernet -> | | -> ethernet -> | switch2 | -> | -> ethernet -> | | -> ethernet -> | switch1 | -> | -> ethernet -> HPNA (TPA311) -> coax -> | splitter | -> coax -> DVR Note that I have the BGW210 RG which does not have the HPNA bridge built into it like the Pace so I had to get the TrendNet TPA311 to initiate the HPNA bridge. The router is a Linksys LRT224 dual WAN router. Then I have the UVerse RG plugged into one of the WAN ports of my router and the Charter modem into the other WAN port. I run the IPTV streams down HPNA via the TrendNet TPA311. Like I said, the possibilities are infinite really.Īnd, in case you're curious, here is my setup. You can then combine a lot of these concepts to create your own custom topology. RG | -> ethernet -> | Router | -> ethernet -> XBOX | | | -> ethernet -> MoCA -> coax -> splitter -> coax -> MoCA -> ethernet -> switch -> RG | -> ethernet -> MoCA -> coax -> | splitter | -> coax -> | splitter | -> coax -> MoCA -> ethernet -> XBOXĪnd finally you can put your own router in the path if you want. Again, I haven't actually tried this, but this is the way I think it should work. I'm using a 3-way splitter to multiplex the HPNA and MoCA signals at the beginning of the path and then another 3-way splitter at the end to demultiplex the signals into individual devices. ![]() | -> ethernet -> MoCA -> coax -> MoCA -> ethernet -> | switch | -> ethernet -> DVRĪnd here I'm trying to run HPNA and MoCA down the same set of coax wires. In this case I have a switch at the end of the MoCA path that supplies the UVerse DVR with the IPTV streams and then there's also an STB connected directly to the RG. You can have a combination of MoCA and direct connections to the RG. RG | -> ethernet -> MoCA -> coax -> | splitter | -> coax -> MoCA -> ethernet -> DVR Keep in mind that the more times you split the coax cable the lower the signal strength on each cable run will be and this may force the MoCA adapters into lower modulation rates and thus slower speeds. Here is a simple diagram of a MoCA only type of setup. Here are but a few of the many ways your network topology could look. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |